RS485 Output Magnetic Flow Meter Fatty Acid Heat BTU
1. Introduction
MLF electromagnetic flowmeter works according to Faraday's law of
electromagnetic induction, and is composed of sensors and
converters. Used to measure the conductivity of liquid or solid. In
general, its conductivity should be greater than 5μs/cm (tap water
and raw water conductivity is about 100 ~ 500μs/cm), and it can
also be used to measure acid, alkali, brine, pulp or pulp and other
media. However, these media cannot contain a large amount of
magnetic substances and bubbles.
3. Specification
| MLF Type | Divided Type | Integrated Type | Explosive Proof Integrated Type | Battery Powered Type | Heat Energy Type |
| Accuracy | ±0.2% or ±0.5% |
| Pipeline Diameter | DN10-DN2000 | DN10-DN600 | DN25-DN2000 |
| Flange | GB, ANSI, JIS, BS, Others |
| Pressure | DN10-DN600 1.0 1.6 2.5 4.0MPa |
| DN700-DN2000 0.6 1.0 1.6MPa |
| Liner Material | CR, PTFE, PU, Hard Rubber, PFA, FEP(F46) |
| Conductivity | ≥5µs/cm(Please contact us if it is less than 5µs/cm) |
| Electrode | 316L SS, Hb, Ta, Ti, Hc, Tungsten Carbide, Others |
| Protection Class | IP65, IP66, IP67, IP68 |
| Medium Temperature | -25~180℃
(Please refer to liner material) | -25~80℃(Please refer to liner material) | -25~180℃
(Please refer to liner material) |
| Ambient Temperature for Accuracy Influence | <±0.1%/10℃ or <±0.25%/10℃ at the ambient temperature of -25~60℃ |
| Repetability | ≤±0.1% or ±0.25% |
| Analog Output Error | ≤±0.02mA |
| Velocity | 0.3~10m/s |
| Electrical connection | M20x1.5 Seal Cartridge, GB1/2, NPT1/2 |
| Output | 4-20mA, Pulse, RS485, Hart, Profibus |
4.Selection of Electrode Materials
| 316L | Good resistance to the corrosion of nitric acid, <5% sulfuric
acid under room temperature, acetic acid, alkaline fluid, sulfite
under certain pressure, seawater and scetic acid, etc. It can be
widely used in petrochemical urea, vinylon. |
| Hb | Good resistance to the all the concentration of hydrochloric acid
below the boiling point, also resistance tothe corrosion of
non-oxidizing acid, alkali, salt like sulfuric acid phosphoric acid
hydrofluoric acid, organic acids. |
| Hc | Resistance to the corrosion of oxidizing acids like metric acid,
mixed acid. The mixture of chromium acid and sulfuric acid, and
salts of oxidative, like Fe3+, Q3+, and some other oxidants, like
hypochlorite salt solution higher than normal tmperature and
seawater. |
| Ti | Resistance the corrosion of seawater, various chlorides,
hypochlorite, oxidizing acid(including fuming nitric acid), and
organic acid or alkali, but don't be resistance to the corrosion of
pure reducint acid(like sulfuric acid, hydrochloric acid). But if
acid includes oxidants(like nitric acid, Fe3+, Q3+), the corrosion
resistance will decrease. |
| Ta | Good corrosion resistance similar to glass. Resistance to the
corrosion of chemical medium(including hydrochloric acid and
fumiing sulfuric acid), but can not be used for sodium hydromide
fluid. |
| Pt-Ir | Have good corrosion resistance of all acid, and can be resistance
to the corrosion of alkali, all salt except aqua regia, ammonium
slat and few other medium |
| Tungsten Carbide | For pulp and sewage, good resistance to solid particle
interference. |
5. Selection of Liner Material
| Liner Material | Main Performance | Application |
| PTFE | 1. Have the most stable chemical properties in plastic and
resistance to boiling hydrochlor and sulfuric acid, nitric acid
aqua regia, strong alkali, and all kinds of organic solvents, but
can not resist the corrosion of chlorine trifluoride, high
temperature nitrogen trifluoride, liquid fluorine, liquid oxygen
and ozone. 2. Low abrasion resistance. 3. Low negative pressure resistance | 1. -25~140ºC 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare medium |
| CR | Oil proof, solvent resistance, oxidatite resistance and the
resistance to the erosion of common medium like acid, alkali, salt,
etc. | 1. <80ºC 2. Be able to measure sewage and mud |
| PU | 1. Very good abrasive resistance, flexibility. 2. Low acid and alkali resistance. | 1. <65ºC 2. Neutral strong abrasion resistance medium |
| Hard Rubber | 1. Good resistance to room temperature, hydrochloric acid, acetic
acid, oxalic acid, ammonia, phosphoric acid and 50% sulfuric acid,
sodium hydroxide, potassium hydroxide 2. Avoid strong oxidants | 1. <80ºC 2. General acid, alkali, salt solution |
| PFA | 1. Can be used for most corrosive medium like acides, alkalis, and
strong oxidant. 2. High material strength, resistance to aging, better than PTFE,
EFP in high temperature 3. Injection molding for higher negative pressure | 1. 40~180ºC 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare mdium |
| FEP(F46) | 1. Hydrophobicity and non-viscous 2. Corrosion resistance is inferior to PFA 3. Negative pressure | 1. 40~180ºC 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare mdium |
6. Configuration
| MLF Series Electromagnetic Flow Meter Configuration |
| Model | MLF |
| Sensor Installation | S | Flange Type Sensor |
| C | Insertion Type Sensor |
| O | Others |
| Pipeline Diameter | 10 | 10mm |
| 15 | 15mm |
| 20 | 20mm |
| ...... | |
| 2000 | 2000mm |
| Electrode Installation | F | Standard Fixed Type |
| Electrode Material | A | 316L SS |
| B | Hb |
| C | Ta |
| D | Ti |
| E | Hc |
| F | Tungsten Carbide |
| G | Others |
| Liner Material | R | Rubber |
| P | PTFE |
| O | Others |
| Pipe Material | B | 304 SS (Standard) |
| C | 316 SS |
| Flange Type | G | GB (Standard) |
| A | ANSI |
| J | JIS |
| B | BS |
| O | Others | |
| Flange Material | A | 304 SS |
| B | 316 SS |
| C | #20 Carbon Steel (Standard) |
| Cover Material | D | 304 SS |
| E | 316 SS |
| F | Carbon Steel+ Epoxy Metallic Paint (Standard) |
| Matching Flange | 0 | Without Matching Flange (Standard) |
| 1 | With Matching Flange |
| Ground Ring | 0 | Without Ground Ring (Standard) |
| 1 | With Ground Ring |
| Rated Pressure | 10 | 1.0MPa |
| 16 | 1.6MPa |
| 25 | 2.5MPa | |
| 40 | 4.0MPa |
| Working Temperature | E | ≤60℃ |
| H | ≤180℃(Divided Type) |
| Type | I | Integrated Type |
| D | Divided Type |
| Output | P | Pulse |
| A | 4-20mA |
| G | RS485 |
| H | Hart |
| Q | Others |
| Power Supply | 0 | 220VAC |
| 1 | 24VDC |
| 2 | Battery-powered |
| Protection Class | 0 | IP65 (Integrated/Divided Type) |
| 1 | IP67 (Divided Type) |
| 2 | IP68 (Divided Type) |
| Other Features | R | Heat Energy Function |
| P | With PT1000 |
| B | Without PT1000 |
| Explosion Proof | 0 | None |
| EX | Explosive Proof |
7.Company Profile
Melan Measurement & Control Instruments is located in Shanghai
City. It is a high-tech manufacturer specialized in the design,
development, manufacturing and sale of measurement and control
instruments.
Our products are widely used in various fields, including
electricity, chemical industry, metallurgy, brewing, oil and gas,
textile, water conservancy, environmential protection, etc.
We own independent-courtyard modemized manufacturing workshops and
an open office building. Melan has accumlated production and
management experience in instruments from European and American and
domestic famous companies.
We own first-class talent team, and all the products have reached
advanced level at home and abroad. We provide our customers with
complete and professional test control solutions and high-tech and
high-quality products.
Melan is your reliable friend and partner. We are willing to try
our best as dedication and perfection as motivation.
8.FAQ
Q: How long will you give me the reply?
A: We will contact you in 5 hours as soon as we can.
Q: What is the warranty of your prducts?
A: Our warranty is 12 months after the shipping date.
Q: What is the lead time of your products?
A: Normally our factory lead time is 10-12 working days.
Q: Can I OEM your products?
A: OEM and ODM customization are welcomed.
Q: What is your MOQ?
A: We have no MOQ limit, small quantity order is acceptable.
Q:What is the transport?
A: Express such as DHL, FedEx, UPS for freight prepaid, and we can
also use your own courier account to do the freight collect. For
more goods we can arrange by air or by sea.
