High Accuracy Water Mag Flow Meter / Magnetic Flowmeter DN200
1. Introduction
The MLF electromagnetic flowmeter works according to Faraday's law
of electromagnetic induction and consists of a sensor and a
converter. Used to measure the conductivity of liquids or solids.
Under normal circumstances, its conductivity should be greater than
5μS/cm (the conductivity of tap water and raw water is about
100-500μS/cm), and it can also be used to measure acids, alkali,
brine, pulp or pulp and other media. But these media cannot contain
a lot of magnetic substances and bubbles.
MLF electromagnetic flowmeter is an instrument for measuring liquid
fluidity. It is widely used in flow measurement in metallurgy,
chemical industry, paper making, environmental protection,
petroleum, textile, food, urban management, water plant and other
industries.
2. Quick Details
MLF electromagnetic flowmeter is explosion-proof design.
Function of low conductivity measurement.
There are nine languages options to meet the needs of different
customers.
It has the function of self-regulation and self-examination.
Different outputs are optional: Hart,RS485 Profibus,4-20mA,
frequency, pulse.
3. Selection of Liner Material
| Liner Material | Main Performance | Application |
| PTFE | 1 It has the most stable chemical properties in plastics, resistant
to boiling hydrogen chloride and sulfuric acid, nitric acid, aqua
regia, strong alkali and various organic solvents, but not
resistant to chlorine trifluoride, high temperature nitrogen
trifluoride, liquid fluorine, and liquid oxygen And ozone
corrosion. 2 Low wear resistance. 3 Low negative pressure resistance. | 1. -25~140℃ 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare medium |
| CR | Oil proof, solvent resistance, oxidatite resistance and the
resistance to the erosion of common medium like acid, alkali, salt,
etc. | 1. ＜80℃ 2. Be able to measure sewage and mud |
| PU | 1. Very good abrasive resistance, flexibility. 2. Low acid and alkali resistance. | 1. ＜65℃ 2. Neutral strong abrasion resistance medium |
| Hard Rubber | 1 Room temperature resistance, hydrochloric acid, acetic acid,
oxalic acid, ammonia, phosphoric acid and 50% sulfuric acid, sodium
hydroxide, potassium hydroxide 2 Avoid strong oxidants | 1. ＜80℃ 2. General acid, alkali, salt solution |
| PFA | 1. Can be used for most corrosive medium like acides, alkalis, and
strong oxidant. 2. High material strength, resistance to aging, better than PTFE,
EFP in high temperature 3. Injection molding for higher negative pressure | 1. 40~180℃ 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare mdium |
| FEP(F46) | 1. Hydrophobicity and non-viscous 2. Corrosion resistance is inferior to PFA 3. Negative pressure | 1. 40~180℃ 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare mdium |
4. Selection of Electrode Materials
| Electrode Material | Main Performance |
| 316L | Good nitric acid corrosion resistance, <5% sulfuric acid, acetic
acid, alkaline liquid, sulfite under certain pressure, sea water,
acetic acid, etc. corrosion at room temperature, can be widely used
in petrochemical urea, vinylon, etc. |
| Hb | Good resistance to all hydrochloric acid with a concentration lower
than the boiling point, and also resistant to corrosion by
non-oxidizing acids, alkalis, sulfuric acid, phosphoric acid,
hydrofluoric acid, and organic acids. |
| Hc | Corrosion resistance to oxidizing acids, such as nitric acid, mixed
acids. A mixture of chromic acid and sulfuric acid, oxidizing salts
such as Fe3+, Q3+, and some other oxidizing agents, such as a
mixture of hypochlorite solution and seawater at higher than normal
temperature. |
| Ti | It is resistant to corrosion by sea water, various chlorides,
hypochlorites, oxidizing acids (including fuming nitric acid),
organic acids or alkalis, but not resistant to corrosion by pure
reducing acids (such as sulfuric acid and hydrochloric acid).
However, if the acid contains oxidants (such as nitric acid, Fe3+,
Q3+), the corrosion resistance will be reduced. |
| Ta | Good corrosion resistance similar to glass. Resistance to the
corrosion of chemical medium(including hydrochloric acid and
fumiing sulfuric acid), but can not be used for sodium hydromide
fluid. |
| Pt-Ir | Have good corrosion resistance of all acid, and can be resistance
to the corrosion of alkali, all salt except aqua regia, ammonium
slat and few other medium |
| Tungsten Carbide | For pulp and sewage, good resistance to solid particle
interference. |
5. Dimensional Sketches
a. Dimension of Converter
Divided Type
Integrated Type
Battery Powered Type
b. Dimension of Sensor
| Pipeline Diameter | Dimension |
| L | W | H |
| 15 | 160 | 95 | 130 |
| 20 | 160 | 105 | 137 |
| 25 | 160 | 115 | 150 |
| 32 | 160 | 135 | 160 |
| 40 | 200 | 145 | 175 |
| 50 | 200 | 160 | 185 |
| 65 | 200 | 180 | 205 |
| 80 | 200 | 195 | 215 |
| 100 | 250 | 215 | 235 |
| 125 | 250 | 245 | 275 |
| 150 | 300 | 280 | 300 |
| 200 | 350 | 335 | 355 |
| 250 | 400 | 400 | 405 |
| 300 | 500 | 455 | 460 |
| 350 | 500 | 515 | 520 |
| 400 | 600 | 575 | 580 |
| 450 | 600 | 635 | 630 |
| 500 | 600 | 710 | 685 |
| 600 | 600 | 835 | 795 |
| 700 | 700 | 905 | 910 |
| 800 | 800 | 1020 | 1030 |
| 900 | 900 | 1120 | 1120 |
| 1000 | 1000 | 1245 | 1250 |
| 1200 | 1200 | 1465 | 1470 |
6. Instrument Testing & Maintenance
The electromagnetic flowmeter has a self-diagnostic function. In
addition to power supply and hardware circuit failures, the system
also alarms other failures in general use. These messages will give
corresponding prompts in the lower right corner of the screen.
1 Maintenance and repair
a) The sensor installation site should meet the requirements of
Section 4, please keep the housing tidy;
b) The transmitter should be placed in a clean, ventilated and dry
place;
c) It needs to be inspected every two years. For high-precision
users, the instrument needs to be submitted for review.
2 Transportation and storage
a) The instrument must be packaged before transportation, and be
handled with care when loading and unloading.
b) The storage place must be dry and ventilated to avoid corrosive
gases, and the ambient temperature should not be too low or too
high;
c) The storage time should not exceed three years.
3. Unpacking inspection
a) The package cannot be opened with a heavy hammer, be careful not
to damage the instrument
b) Check the contents carefully according to the packing list.
7. Product Photos
